Screwless Unfinished Wood Switch Plates

This is the size of the USA Standard Decora opening size which we have been making for years.

Recently some companies have made much larger Decora Switches, Rockers, Dimmers, and Duplex Decora Receptacles. 

They force you into buying and using their plastic switch plate covers.

 

We can make the opening to fit these larger sizes, but there is an extra charge for these new sizes from Hubbell, Lutron, Leviton, and others.

So please check your measurements, and we need to know if you are using some of these larger devices before we start to manufacture your wooden switch plate covers

 

 

Screwless wood switch plate sizes

Single size is 5-3/4" tall by 3-1/2" wide

Double size is 5-3/4" tall by 5-3/4" wide

Triple size is 5-3/4" tall by 7-1/2" wide

Quad size is 5-3/4" tall by 9’’ wide

 

If you have a question about what you are ordering, just give us a call, as there are no returns on these custom screwless wallplates if you order incorrectly.  If there is a problem with our manufacturing, we will remake them or correct the problem at no charge.

 

If you don't see the configuration you need, we can customize a plate for you with the locations of the receptacles or switches in the exact order that you need for the locations on the plate cover.  So give us a call at 800-260-1181, and we can discuss this with you.

 

 

Also available in MDF simulated wood for a very smooth paintable finish.

(shown with screws)

 

 

 

 ALL CONFIGURATIONS ARE AVAILABLE FOR UP TO 4 GANGS IN OUR HANDCRAFTED SWITCH PLATES IN UNFINISHED WOOD

 

Custom Wood Stain Finishes are Available
Natural 209	Golden Oak 210B	Provincial 211
Red Oak 215	Puritan Pine 218	Ipswich Pine 221
Sedona Red 222	Colonial Maple 223	Special Walnut 224
Red Mahogany 225	Early American 230	Gunstock 231
Red Chestnut 232	English Chestnut 233	Cherry 235
Fruitwood 241	Golden Pecan 245	Pickled Oak 260
Driftwood 2126	Dark Walnut 2716	Ebony 2718
Jacobean 2750

African Mahogany	Alder	Ash	Birdseye Maple *	Birdseye Pine	Bloodwood	Poplar	Yellow Pine	Brazilian Cherry
Butternut	Canary *	Cherry	Coco Bolo Not available any longer .	Douglas Fir	Hemlock	Hickory	Honduras Mahogany	Idaho White Pine
Western Red Cedar	Rift Cut White Oak	Koa*	Light Bamboo*	Lyptus*	Maple, Eastern White	Maple, Western	Red Oak	White Oak
Pecan	Philippine Mahogany		Purple Heart*	Red Birch	White Birch	Redwood*	Vertical Grain White Oak	White Oak Quarter Sawn
Teak*	Tennessee Cedar or Eastern Cedar	Walnut	Walnut, Peruvian

Applewood	Aspen	Bamboo Carmelized Horizontal Grain	Bamboo Natural Horizontal Grain	Bamboo Carmelized Vertical Grain	Bamboo Natural Vertical Grain	Basswood
Beech Wood	Black Walnut	Bocote	Bubinga		Chechen	Chestnut, Wormy
Claro Walnut	Curly Maple	Cypress	East Indian Rosewood	Ebony Macassar	English Walnut	Kingwood
Goncalo Alves	Hard Maple	Heart Pine	Honduran Rosewood	Jatoba	Kentucky Tree	Lacewood
Locust	Mahogany Santos	Mesquite	Mulberry	Narra Wood	Paulownia	Persimmon
Peruvian	Ponderosa Pine	Quartered	Quilted Maple	Bolivian Rosewood	Sapele	Sassafras
Soft Maple	Spanish Cedar	Sycamore	Sycamore Quarter- Sewn	Tulip Wood	Wenge Wood	Western Cedar
White Cedar	White Pine	Yellow Cedar	Yellow Heart	Zebra Wood	Zirconite Wood

 SCREWLESS SWITCH PLATES INSTALLATION INSTRUCTIONS 

See the installation video Here

WHEN YOU RECEIVE YOUR SCREWLESS WALLPLATES, THERE WILL BE A WHITE WALL HOUSING THAT IS IN TWO SECTIONS, MARKED FACE THE WALL, AND FACE OUT.  THIS IS VERY IMPORTANT, AS THESE WHITE WALL HOUSINGS NEED TO BE IN THE RIGHT DIRECTION FOR THESE TO BE SNAPPED TOGETHER WITH THE WHITE SECOND PART OF THE WALL HOUSING THAT IS ATTACHED TO THE BACKS OF THE WOOD WALL PLATES.   

TO GET THE ELECTRICAL DEVICE AS FAR TO THE FRONT OF THE FACE SIDE OF THE WOOD SWITCH PLATE, IT IS IMPORTANT TO SLIDE THE WHITE HALF OF THE WALL HOUSING INTO THE BACK OF THE ELECTRICAL DEVICE.    HERE IS HOW THIS IS DONE. 

1.  FIRST TURN OFF THE POWER TO THE ELECTRICAL DEVICE.

2.  COMPLETELY REMOVE THE SCREW OR SCREWS THAT HOLD THE TOP PART OF THE ELECTRICAL DEVICE TO THE BOX IN THE WALL (THESE ARE USUALLY THE TOP SCREWS) AND SET THEM  ASIDE.

3.  NOW LOOSEN THE OTHER SCREW OR SCREWS, SLIDE THE WHITE WALL HOUSING TOP SECTION IN THE BACK OF THE AREA WHERE YOU TOOK OUT THE SCREW FROM THE ELECTRICAL DEVICE, AND PULL IT DOWN A BIT BEHIND THE ELECTRICAL DEVICE.   NOW YOU SHOULD BE ABLE TO SLIDE THE BOTTOM PART OF THE WHITE WALL HOUSING PAST THE ELECTRICAL DEVICE.  NOW PUSH THE WHITE WALL HOUSING IN THE BACK OF THE ELECTRICAL DEVICE BY PUSHING IT UP, SO THE WHITE HOUSING IS NOW THE  IN BACK OF THE ELECTRICAL DEVICE.  THE WHITE WALL HOUSING MAY NEED TO SLIDE LEFT OR RIGHT A LITTLE, TO LINE IT UP WITH THE ELECTRICAL DEVICE.  THIS IS HOW THE FINISHED PRODUCT SHOULD LOOK.

  OR   BACKS OF WOOD 

4.  NOW THAT THE ELECTRICAL DEVICE IS IN FRONT OF THE WHITE WALL HOUSING, SCREW IN THE SCREW, OR SCREWS THAT WERE REMOVED IN STEP TWO, AND TIGHTEN THEM UP SO THE SCREW CAN NOW GO INTO THE ELECTRICAL DEVICE AND THROUGH THE WHITE WALL HOUSING, AND NOW INTO THE BOX IN THE WALL.  THEN TIGHTEN ALL THE SCREWS.  YOU ARE NOW READY TO SNAP ON THE WOOD SWITCH PLATE COVER TO THE HOUSING, WHICH IS NOW ATTACHED BEHIND THE ELECTRICAL DEVICE AND MOUNTED TO THE WALL.  

LIKE THIS  OR ONE OF THESE 

WE HAVE A VIDEO OF THIS INSTALLATION THAT IS AT THE TOP OF THIS PAGE, SO PLEASE CHECK OUT HOW WE SUGGEST YOU MOUNT THESE SO THE RECEPTACLE IS AS FAR AS POSSIBLE TO THE FRONT SIDE OF THE FLAT SURFACE FRONT OF THE PLATE.  IF YOU NEED SOME HELP, BY ALL MEANS, GIVE US A CALL AT 800-260-1181 AND WE WILL HAVE OUR WOOD CRAFTERS RETURN YOUR CALL AND WALK YOU THROUGH THIS INSTALLATION PROCESS.