Full Pocket Audio Video Floor Box/1 duplex/6 low voltage

 

 

 

 

 

• Full Stage Pocket Body Size = 8.000” W x 3.500” H x 7.187” D
• Full Stage Pocket Lid & Mounting Flange Size = 10.500” W x 1.000” H x 10.500” D
• Full Stage Pocket Connector Capacity = Up to 12 “Connectrix”, Neutrik®, or Switchcraft®
• Full Stage Pocket Cutout Dimensions = 8.500" W x 8.500" H
• Full Stage Pocket Material = CRS Steel and/or Solid Half Hard Brass
• Full Stage Pocket Panel Capacity =
• (2) #PNL-100 Series “CONNECTRIX” Panels OR
• (2) #PSW-100 Series Switchcraft® Panels OR
• (2) #PE Series Single Gang Electric Duplex Switch Box Panels OR
• (1) #FP3E Series Triple Gang Electric Duplex Switch Box Panel OR
• (1) #PNL-120 Series “Connectrix” Panel

 

 

 

 

 

 

Neutrik® "D" and Switchcraft® "E" Connector Mounts
Custom Cut Connector Mounts
Switchcraft® "D" Connector Mounts

“CONNECTRIX” CONNECTORS COMBINE NEUTRIK® “D” AND SWITCHCRAFT® “E” MOUNTING HOLE PATTERNS FOR GREATER FLEXIBILITY

The “Connectrix” system connectors may be used in any of the “Connectrix” panels utilizing the popular mounting pattern of the Neutrik “D” and Switchcraft “E” series mounting patterns. Connectors using the generous rectangular “Connectrix” cutout will add to a growing array of adapter-mounted standard connectors. The adapter mount is plastic and provides ground isolation between the panel and connector. Click on the links above for our current selection of stock “Connectrix” system connectors.

When ordering, please specify the model number and type of connector as well as the panel model number (#PNL-100 Series, #PNL-120 Series, or #PSW-100 Series) the connectors will be loaded into. *NOTE: Specific High Density (HD) and Sub-D pattern connectors will require either 2 or 3 “Connectrix” Horizontal Spaces or 2 or 3 “Connectrix” Vertical Spaces, depending on the connectors selected. Connectors may be loaded into panels with nut certs and nut/bolts or black aluminum pop rivets.

 

 

 

 

 

 

"Connectrix" Panels combine Neutrik® "D" and Switchcraft® "E" Connector Mounts
Custom Cut Panels with Custom Connector Mounts
Utilize Switchcraft® "D" Connector Mounts

“CONNECTRIX” SYSTEM PANEL DESCRIPTION

Much pre-cut stock #PNL-100 Series, #PNL-120 Series “Connectrix” System connector panels, and #PSW-100 Series Switchcraft® connector panels are available for the Full Stage Pocket. Standard "Connectrix" and Switchcraft® Panels are created from high-strength, tough, aircraft aluminum alloy (6061-T6) that is 1/16" (.062") or 1/8" (.125") thick. The standard panels mount with (4 or 6) self-tapping screws. Each panel is CNC machined to precisely mate with the designated connectors and in the pocket mounting holes. Each Standard "Connectrix" and Switchcraft® Panel is finished with oven cured semi-gloss black powder coat.

Most panels provide header space for custom engraving which is fast and easily accomplished on a separate dedicated CNC engraving machine. The finished panels show bright aluminum in the engraved characters and need not be backfilled.  Arnev's standard panels are flat, strong, and rigid like the typical thinner mild steel panels. Because the panels are machined and not punched they stay flat and undistorted, unlike punched panels which distort the punching process. The machined “Connectrix” style cutouts combine popular mounting patterns of the Neutrik “D” series and Switchcraft “E” series connectors with a generous rectangular cutout that mates with a growing array of adapter-mounted standard connectors. The adapter mount is plastic and provides ground isolation between the panel and connector.

Using the “Connectrix” system panel it is possible to mount any combination of modular jacks (RJ45, RJ11, etc.), BNCs, dual RCAs, mic jacks, speaker jacks, and numerous other standard connectors without a single custom punch. This system provides for more connectors and mounting options in stock standard Arnev panels. The benefit is faster order turnaround and lower cost. Less custom fabrication for custom spec results with off-the-shelf stock prices.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• (1) Stage Pocket Body with Trim Bezel Mounting Flange
• (1) Lid
• (2) Hinge Pins
• (2) Springs
• (8) #8 Self-Tapping Sheet Metal/Wood Screws
• (1) Slot Closure

 

 

 

 

 

When ordering Stage Pockets please specify the following:
• Stage Pocket Model Number: Example - #122SLBK
• Stage Pocket Model Name (size): Mini | Half | Full | Double Wide
• Stage Pocket Finish Type (Lid & Mounting Flange): Black, Brass, Copper Vein, Stainless Steel
• Stage Pocket Lid Type: Carpet Lids (CL), Locking Lids (LL), Standard Lids (SL)
• Optional Stage Pocket Panel(s) Model Numbers: Example - #PNL-106
• Optional Connectors to be loaded into Panel(s): Example - #C15101
• Location of Connectors mounted into Panel(s): Example - Top Left
• Type of Connector Mounts: Nuts/Bolts or Black Aluminum Pop Rivets

 

 

 

 

 

 

 

 

 

 

 

 

LARGE CAPACITY: The Full Stage Pocket accommodates #PNL-100 Series Panels, #PSW-100 Series Panels, #PNL-120 Series Panels, and #PE Series Panels in an interchangeable multi-panel system making for easy custom configurations. Two (2) optional #PNL-100 Series Panels or one (1) optional #PNL-120 Series Panel will mount up to 12 "CONNECTRIX", Neutirk®, and/or Switchcraft® type connectors*. Two (2) optional #PSW-100 Series Panels will mount up to 12 Switchcraft® type connectors.

DURABLE CONSTRUCTION: Welded steel construction of Full Stage Pocket Lid, Mounting Flange, and Pocket Body resist bending under even the most severe stage loads. The Lid and Mounting Flange are made from 1/8" (nominally 11 ga. (.120") CRS) thick steel while the Pocket Body is made from 16 ga. (.062") thick CRS steel.

SPRING LOADED HINGE PINS: Removable spring-loaded hinge pins permit the easy exchange of lids for Carpet Lid (CL), Locking Lid (LL), Standard Lid (SL), and custom application lids.

CABLE WAY SLOTS: Generous 3/8" x 8" Cable Way Slots permit easy cable exit from pocket(s), even for large gauge cables. A Cable Way Slot Closure channel closes the slot when not in use.

EASY INSTALLATION: Easy installation into 8.5" x 8.5" square cutout on the stage floor. Open easy access from the top or back of the stage pocket allows simple connector/panel terminations.

DECORATOR FINISHES: Scratch/wear-resistant finish, oven-cured powder coat electro-static applied inside and outside entire Full Stage Pocket. Decorator neutral Antique Copper Vein and Textured Black finishes are standard. A Solid Brass Lid and Mounting Flange, as well as a Solid Stainless Steel Lid and Mounting Flange with brushed finishes, are also available by special order.

RUBBER LID STOPS: Rubber lid stops set into recessed mount cradle the lid to prevent lid rattle.

 

 

 

 

 

 

 

 

STANDARD POCKET MATERIALS: Arnev's Full-size Standard Vertical Slant Panel Stage Pocket Lids and Mounting Flanges are made of 1/8" (nominally 11 ga. (.120") thick CRS steel while the Full Stage Pocket Body is made from 16 ga. (.062") thick CRS steel. The exception to this is the Brass Full Stage Pocket Lid and Mounting Flange which is made of 1/8" (nominally 11 ga. (.120")) thick Half Hard Solid Brass with a Stage Pocket Body made from 16 ga. (.062") thick CRS steel.

Full Stage Pockets are manufactured with the following materials:
• Lids & Mounting Flanges are made of 1/8" (nominally 11 ga. (.120" thick)) CRS Steel
• Pocket Body is made from 16 ga. (.062" thick) CRS Steel
• Brass Lid & Mounting Flanges are made of 1/8" (nominally 11 ga. (.120" thick)) Half Hard Solid Brass

 

 

 

 

 

 

PACKAGES: Arnev's Full Stage Pocket Packages were designed to meet customer requests to "package" our most frequently used products into simple, all-in-one, complete "Connectivity" Solutions.

 

 

 

 

 

UL LISTED: UL Listed compliance Standard 514A file FLOOR BOX 44LK Suitable for raised floor applications.