Brass Punched Heart Design Switch Plates

These are our Brass Punched Heart Switch plates. These are made of a heavy .042 gauge metal, very sturdy.

USA MADE

PULL THIS PAGE DOWN TO START SHOPPING

SEE ALL THE CONFIGURATIONS

Prices Starting at: $1.87

Step 1: NEW FEATURE! Choose all the quantities of the configurations in one step, then click the Add to Cart button, it's as easy as 1-2-3!	Price	Buy
A. Single Switch (SS)	$1.87	+ -
B. Outlet Cover (OC) 2 oval shaped holes ONLY AVAILABLE IN THE BORDER DESIGN, NO HEART, NO ROOM ON THE PART.	$1.87	+ -
C. Double Switch (DS)	$2.87	+ -
D. Combo Switch (CS)	$2.87	+ -
F. Groundfault/Rocker (GF) ONLY AVAILABLE IN THE BORDER DESIGN, NO HEART, NO ROOM ON THE PART.	$1.87	+ -
H. Groundfault/Single Switch (GFSS)	$2.87	+ -
J. Triple Groundfault/Rocker (TGF) ONLY AVAILABLE IN THE BORDER DESIGN, NO HEART, NO ROOM ON THE PART.	$3.87	+ -
K. Double Groundfault/Rocker (DGF) ONLY AVAILABLE IN THE BORDER DESIGN, NO HEART, NO ROOM ON THE PART.	$2.87	+ -
M. Groundfault/Double Toggle (GFDT) ONLY AVAILABLE IN THE BORDER DESIGN, NO HEART, NO ROOM ON THE PART.	$2.87	+ -
N. Quad Groundfault/Rocker (QGF) ONLY AVAILABLE IN THE BORDER DESIGN, NO HEART, NO ROOM ON THE PART.	$4.87	+ -
L. Quad Switch (QS)	$4.87	+ -
O. Outlet Cover/Triple Switch (OCTS)	$4.87	+ -
P. Groundfault/Triple Switch (GFTS)	$4.87	+ -
Q. Groundfault/Double Switch (GFDS)	$3.87	+ -
U. Six Switch (6S)	$6.87	+ -
V. Seven Switch (7S)	$7.87	+ -
W. Eight Switch (8S)	$8.87	+ -

A Very durable plated brass finish, along with telephone and cable TV, CAT5, and all the other accessories are available. These switch plate covers are all mid-sized covers, and slightly larger but not jumbo-sized. A slightly larger size usually will cover up bad drywall cuts around the electrical receptacle box openings, whereas a standard-size light switchplate may not. Also, this is to cover up any old paint lines or wallpaper lines. Some of the configurations do not have a punched heart design, as there is no room to fit a heart on some configurations, like the outlet covers and the Groundfault type. And some configurations have both a heart and a punched border design and they all complement each other. See our chart below. THIS PRODUCT IS MADE IN THE USA.

For Telphone Jacks, Cable TV Jacks, CAT5

along with Switchplates

CLICK HERE

Metal and Porcelain Enamel Switchplate sizing:

One gang switch plates (Singles-A, Single Outlets-B, Single Groundfaults-F)	3 " wide by 5 " high
Two gang switch plates (Doubles-C, Combo's-D, Double Groundfaults-K, etc.)	4 7/8" wide by 5 " high
Three gang switch plates (Triples-E, Triple Groundfaults-J, Groundfault/Double Switch-Q etc.)	6 11/16" wide by 5 " high
Four gang switch plates (Quad Switches-L, Outlet Cover/Triple Switch-O, etc.)	8 1/2" wide by 5 " high
Five gang switch plates (5-Switch-5S, 5-Groundfault/Rocker-5 GF/R)	10 5/16" wide by 5 " high
Six gang switch plates (6-Switch-6S, 6-Groundfault/Rocker-6 GF/R)	12 1/16" wide by 5 " high
Seven gang switch plates (7-Switch-7S, 7-Groundfault/Rocker-7 GF/R)	13 7/8" wide by 5 " high
Eight gang switch plates (8-Switch-8S, 8-Groundfault/Rocker-8 GF/R)	15 3/4" wide by 5 " high

Includes matching screws. Click here for Switchplate Sizes

These switchplates are available in the following configurations:
NOTE: B,F,I,J,K,M,N,R,S,T,U,V,W,X,Y,Z,AA,BB are in our Punched Border Design, (Not Hearts), but are intended to go with the heart design. Some configurations such as D, G, H, O, P, Q, have small hearts around the switch opening. All light switch plates can be installed with the outlet on either the right or the left side, by simply turning the part and flipping it over.

Click Here to order other Telephone, CAT5, CableTV/Satellite,

Blank Inserts for Type F (ground fault, or decora type) switchplates.

Also for Banana Jacks, Speaker wire inserts, Dimmer knob inserts,

RCA, DVI, HDMI, and other accessories in 6 colors.

Check out our " Socketops Peel and Stick"

by clicking on the "Detailed Images" above

All our switchplates are referred to as a mid-sized part. They are a bit larger than the standard size, but not oversized. Having them a bit larger usually covers up any irregularities that could have occurred when the drywall was cut for the electrical box openings, which does occur quite often. Also, this would cover up any outlines, or paint or wallpaper color differences left by the old light switch cover. However, they are not so oversized that they don't fit into spaces usually allotted for the standard sizes.

Our switchplates can be flipped up-side-down to fit your particular electrical configuration. Let's say you have a combination style, with the switches on one side, and the outlets on the other side. You can just flip the part over, and this works great in all cases.

Step 1: NEW FEATURE! Choose all the quantities of the configurations in one step, then click the Add to Cart button, it's as easy as 1-2-3!
A. Single Switch (SS), B. Outlet Cover (OC) 2 oval shaped holes ONLY AVAILABLE IN THE BORDER DESIGN, NO HEART, NO ROOM ON THE PART., C. Double Switch (DS), D. Combo Switch (CS), F. Groundfault/Rocker (GF) ONLY AVAILABLE IN THE BORDER DESIGN, NO HEART, NO ROOM ON THE PART., H. Groundfault/Single Switch (GFSS), J. Triple Groundfault/Rocker (TGF) ONLY AVAILABLE IN THE BORDER DESIGN, NO HEART, NO ROOM ON THE PART., K. Double Groundfault/Rocker (DGF) ONLY AVAILABLE IN THE BORDER DESIGN, NO HEART, NO ROOM ON THE PART., M. Groundfault/Double Toggle (GFDT) ONLY AVAILABLE IN THE BORDER DESIGN, NO HEART, NO ROOM ON THE PART., N. Quad Groundfault/Rocker (QGF) ONLY AVAILABLE IN THE BORDER DESIGN, NO HEART, NO ROOM ON THE PART., L. Quad Switch (QS), O. Outlet Cover/Triple Switch (OCTS), P. Groundfault/Triple Switch (GFTS), Q. Groundfault/Double Switch (GFDS), U. Six Switch (6S), V. Seven Switch (7S), W. Eight Switch (8S)