Full Pocket AV Floor Box with room for up to one duplex and up to six low voltage devices.

Full-Size AV floor box with room for up to one duplex and up to six low voltage devices. The lid will close, the chords will come out the front section. 
 THIS PRODUCT MADE IN THE USA
 
 
 
  • $293.88

Please fill in the dropdown to continue!

Qty:  
  • SKU
    Full Pocket
 
Audio Video Table Top Pocket Box, with up to 12 optional low voltage connectors available in one box for you to customize.  Panels included at $293.88 in black for carpet flange pocket or regular full pocket.
 
The Full Stage Pocket has the panel capacity for either:
• (2) #PNL-100 Series "Connectrix" Panels or
• (2) #PE Series Single Gang Electric Duplex Switch Box Panels or
• (1) #PNL-100 Series and One #PE Panel
The Full Stage Pocket has the connector capacity for either:
• (12) "Connectrix" Connectors or
• (12) Neutrik® Connectors or
• (12) Switchcraft® Connectors or
• (6) "Connectrix", Neutrik®, or Switchcraft® Connectors and
  (1) #PE Electric Duplex Switch Box
Utilizing Arnev's "Connectrix" System will allow mounting of up to 12 "Connectrix", Neutrik®, Switchcraft®, and/or Custom Connectors in the Full Stage Pocket. All Arnev Full Stage Pockets are welded steel construction, with a 1/8" (nominally 11 ga. (.120")) thick CRS steel Lid and Mounting Flange and a 16 ga. (.062") thick Pocket Body. The Full Stage Pocket resists bending under even the most severe stage loads.

Removable spring loaded hinge pins permits easy exchange of lids for carpet lids, locking lids, standard lids, and other custom application lids. A generous cable way slot of 3/8" x 8" permits easy cable exit from the stage pocket, even for large gauge cables. A cableway slot closure channel closes the slot when not in use. The Full Stage Pocket has an easy installation into 8.5" x 8.5" cutout in the stage floor. Open easy access from top or back of the Full Stage Pocket to connector panels makes for easy installation.

A scratch/wear resistant finish, oven cured powder coat is electro-staticly applied inside and outside the entire Stage Pocket. Decorator neutral Antique Copper Vein or Textured Black finishes are standard. A Solid Brass Lid and Mounting Flange as well as Solid Stainless Steel Lid and Mounting Flange are also available by special order. The Full Stage Pocket's solid rubber Lid Stops cradle the lid to prevent lid rattle.

Arnev's Standard Vertical Slant Panel Stage Pocket Systems offer "Connectivity" Solutions with a flexible, reliable, and simplistic design. The flexible design of the Standard Vertical Slant Panel Stage Pocket Lid, Mounting Flange and Pocket Body along with Custom and Prefabricated Aluminum "Connectrix" (Neutrik®/Switchcraft® combo cutout) Panels, Switchcraft® Panels, and our large selection of "Connectrix" (Neutrik®/Switchcraft® combo cutout), Switchcraft®, and Custom Connectors allow the Stage Pockets to be installed in many different applications. These applications include educational, institutional, and liturgical settings. Within these applications various audio, communications, control, data, electric AC power, video, and voice terminations are possible, allowing for a complete Stage Pocket System.

Arnev's Standard Vertical Slant Panel Stage Pockets are available in a variety of sizes (Mini, Half, Full, and Double Wide) making them flexible in both form and function and able to meet your individual requirements. All Standard Vertical Slant Panel Stage Pockets are UL Listed except for the Mini Pocket.
 
 
 
 
 
SPECIFICATIONS
 

Full Stage Pocket Body Size = 8.000” W x 3.500” H x 7.187” D
Full Stage Pocket Lid & Mounting Flange Size = 10.500” W x 1.000” H x 10.500” D
Full Stage Pocket Connector Capacity = Up to 12 “Connectrix”, Neutrik®, or Switchcraft®
Full Stage Pocket Cutout Dimensions = 8.500" W x 8.500" H
Full Stage Pocket Material = CRS Steel and/or Solid Half Hard Brass
Full Stage Pocket Panel Capacity =
• (2) #PNL-100 Series “CONNECTRIX” Panels OR
• (2) #PSW-100 Series Switchcraft® Panels OR
• (2) #PE Series Single Gang Electric Duplex Switch Box Panels OR
• (1) #FP3E Series Triple Gang Electric Duplex Switch Box Panel OR
• (1) #PNL-120 Series “Connectrix” Panel
 
 
 
 
 
 
CONNECTORS
 
 
Connectrix
Custom Cut
Switchcraft®

Neutrik® "D" and Switchcraft® "E" Connector Mounts
Custom Cut Connector Mounts
Switchcraft® "D" Connector Mounts

“CONNECTRIX” CONNECTORS COMBINE NEUTRIK® “D” AND SWITCHCRAFT® “E” MOUNTING HOLE PATTERNS FOR GREATER FLEXIBILITY

The “Connectrix” system connectors may be used in any of the “Connectrix” panels utilizing the popular mounting pattern of the Neutrik “D” and Switchcraft “E” series mounting patterns. Connectors using the generous rectangular “Connectrix” cutout will add to a growing array of adapter-mounted standard connectors. The adapter mount is plastic and provides ground isolation between the panel and connector.Click on the links above for our current selection of stock “Connectrix” system connectors.

When ordering, please specify model number and type of connector as well as panel model number (#PNL-100 Series, #PNL-120 Series, or #PSW-100 Series) the connectors will be loaded into. *NOTE: Specific High Density (HD) and Sub-D pattern connectors will require either 2 or 3 “Connectrix” Horizontal Spaces or 2 or 3 “Connectrix” Vertical Spaces, depending on connectors selected. Connectors may be loaded into panels with nutcerts and nut/bolts or black aluminum pop rivets.
 
 
 
 
 
 
PANELS
 
 
Connectrix
Custom Cut
Switchcraft®

"Connectrix" Panels combine Neutrik® "D" and Switchcraft® "E" Connector Mounts
Custom Cut Panels with Custom Connector Mounts
Utilize Switchcraft® "D" Connector Mounts

“CONNECTRIX” SYSTEM PANEL DESCRIPTION

Many pre-cut stock #PNL-100 Series, #PNL-120 Series “Connectrix” System connector panels and #PSW-100 Series Switchcraft® connector panels are available for the Full Stage Pocket. Standard "Connectrix" and Switchcraft® Panels are created from high strength, tough, aircraft aluminum alloy (6061-T6) that is 1/16" (.062") or 1/8" (.125") thick. The standard panels mount with (4 or 6) self-tapping screws. Each panel is CNC machined to precisely mate with the designated connectors and in the pocket mounting holes. Each Standard "Connectrix" and Switchcraft® Panel is finished with oven cured semi-gloss black powder coat.

Most panels provide header space for custom engraving which is fast and easily accomplished on a separate dedicated CNC engraving machine. The finished panels show bright aluminum in the engraved characters and need not be back filled.  Arnev's standard panels are flat, strong, and rigid like the typical thinner mild steel panels. Because the panels are machined and not punched they stay flat and undistorted unlike punched panels which distort in the punching process. The machined “Connectrix” style cutouts combine popular mounting patterns of the Neutrik “D” series and Switchcraft “E” series connectors with a generous rectangular cutout that mates with a growing array of adapter-mounted standard connectors. The adapter mount is plastic and provides ground isolation between the panel and connector.

Using the “Connectrix” system panel it is possible to mount any combination of modular jacks (RJ45, RJ11 etc.), BNCs, dual RCAs, mic jacks, speaker jacks and numerous other standard connectors without a single custom punch. This system provides for more connectors and mounting options in stock standard Arnev panels. The benefit is faster order turn around and lower cost. Less custom fabrication for custom spec results with off-the-shelf stock prices.
 
 
 
 
 
PE
PNL-100
 
   
SERIES PANELS
SERIES PANELS
     
#PE
#PNL-100
 
 
 
 
 
 
 
#PNL-102
 
 
 
 
 
 
 
#PNL-103
 
 
 
 
 
 
#PNL-104
 
 
 
 
 
 
#PNL-105
 
 
 
 
 
 
#PNL-106
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
   
 

• (1) Stage Pocket Body with Trim Bezel Mounting Flange
• (1) Lid
• (2) Hinge Pins
• (2) Springs
• (8) #8 Self Tapping Sheet Metal/Wood Screws
• (1) Slot Closure
 
 
 
 
 
 
ORDERING
 

When ordering Stage Pockets please specify the following:
Stage Pocket Model Number: Example - #122SLBK
Stage Pocket Model Name (size): Mini | Half | Full | Double Wide
Stage Pocket Finish Type (Lid & Mounting Flange): Black, Brass, Copper Vein, Stainless Steel
Stage Pocket Lid Type: Carpet Lids (CL), Locking Lids (LL), Standard Lids (SL)
Optional Stage Pocket Panel(s) Model Numbers: Example - #PNL-106
Optional Connectors to be loaded into Panel(s): Example - #C15101
Location of Connectors mounted into Panel(s): Example - Top Left
Type of Connector Mounts: Nuts/Bolts or Black Aluminum Pop Rivets
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

LARGE CAPACITY: The Full Stage Pocket accomodates #PNL-100 Series Panels, #PSW-100 Series Panels, #PNL-120 Series Panels, and #PE Series Panels in an interchangeable multi-panel system making for easy custom configurations. Two (2) optional #PNL-100 Series Panels or one (1) optional #PNL-120 Series Panel will mount up to 12 "CONNECTRIX", Neutirk®, and/or Switchcraft® type connectors*. Two (2) optional #PSW-100 Series Panels will mount up to 12 Switchcraft® type connectors.

DURABLE CONSTRUCTION: Welded steel construction of Full Stage Pocket Lid, Mounting Flange, and Pocket Body resist bending under even the most severe stage loads. The Lid and Mounting Flange is made from 1/8" (nominally 11 ga. (.120") CRS) thick steel while the Pocket Body is made from 16 ga. (.062") thick CRS steel.

SPRING LOADED HINGE PINS: Removable spring loaded hinge pins permit easy exchange of lids for Carpet Lid (CL), Locking Lid (LL), Standard Lid (SL) and custom application lids.

CABLE WAY SLOTS: Generous 3/8" x 8" Cable Way Slots permit easy cable exit from pocket(s), even for large gauge cables. A Cable Way Slot Closure channel closes the slot when not in use.

EASY INSTALLATION: Easy installation into 8.5" x 8.5" square cutout in stage floor. Open easy access from the top or back of the stage pocket allows simple connector/panel terminations.

DECORATOR FINISHES: Scratch/wear resistant finish, oven cured powder coat electro-static applied inside and outside entire Full Stage Pocket. Decorator neutral Antique Copper Vein and Textured Black finishes are standard. A Solid Brass Lid and Mounting Flange as well as Solid Stainless Steel Lid and Mounting Flange with brushed finishes are also available by special order.

RUBBER LID STOPS: Rubber lid stops set into recessed mount cradle the lid to prevent lid rattle.
 
 
 
 
 
 
 
 

DECORATOR FINISHES: Arnev's Full size Standard Vertical Slant Panel Stage Pockets come with a scratch/wear resistant finish, oven cured powder coat electro-static applied inside and outside the entire Full Stage Pocket. Decorator neutral Antique Copper Vein and Textured Black finishes are standard. A Solid Brass Lid and Mounting Flange as well as a Solid Stainless Steel Lid and Mounting Flange with a brushed finish are also available by special order*.
If you need a custom color, check out our Custom Color Finishes.  You will need to ask for a quantity quote, or a custom color quote at 800-260-1181.  Please allow 2-3 weeks for delivery on these custom colors.
 
 
 
 
 
 
 
   
 

STANDARD POCKET MATERIALS: Arnev's Full size Standard Vertical Slant Panel Stage Pocket Lids and Mounting Flanges are made of 1/8" (nominally 11 ga. (.120") thick CRS steel while the Full Stage Pocket Body is made from 16 ga. (.062") thick CRS steel. The exception to this is the Brass Full Stage Pocket Lid and Mounting Flange which is made of 1/8" (nominally 11 ga. (.120")) thick Half Hard Solid Brass with a Stage Pocket Body made from 16 ga. (.062") thick CRS steel.

Full Stage Pockets are manufactured with the following materials:
• Lids & Mounting Flanges are made of 1/8" (nominally 11 ga. (.120" thick)) CRS Steel
• Pocket Body is made from 16 ga. (.062" thick) CRS Steel
• Brass Lid & Mounting Flanges are made of 1/8" (nominally 11 ga. (.120" thick)) Half Hard Solid Brass
 
 
 
 
 
 
 
 

PACKAGES: Arnev's Full Stage Pocket Packages were designed to meet customer requests to "package" our most frequently used products into simple, all-in-one, complete "Connectivity" Solutions.
 
 
 
 
 
 
 
 

UL LISTED: UL Listed compliance Standard 514A file FLOOR BOX 44LK Suitable for raised floor applications.
UL Listed
UL Listed Copy
 
Sales Taxes please note:  All our AV boxes are shipped direct to you from our California facility and if you are having the box shipped to you in California we will be calculating the sales tax needed for the transaction.  By law, we are required to charge and pay California sales taxes when a product is shipped to a customer in California.

 

  • Step #5. Please choose for a Wood floor, or a new Concrete pour type WITH OR WITHOUT POWER RECEPTACLE.
    Please choose for a Wood floor, or a new Concrete pour type WITH OR WITHOUT POWER RECEPTACLE., Wood Floors, Concrete Pour No Power (102-BBX), Concrete Pour With Power (ISO 102-BBX)
  • Step #1. Choose two small panels needed for this box
    CHOOSE TWO SMALL PANELS FOR THIS BOX, PNL 100 with no holes, PNL 102 with two holes, PNL 103 with three holes, PNL 104 with four holes, PNL 105 with five holes, PNL 106 with six holes, PE for duplex receptacle, PNL 107 FOR DECORA RECEPTACLE
  • Step #2. Choose the second panel for this box
    Please choose the second panel for this box, PNL 100 with no holes, PNL 102 with two holes, PNL 103 with three holes, PNL 104 with four holes, PNL 105 with five holes, PNL 106 with six holes, PE for duplex receptacle, PNL 107 for Decora receptacle
  • Step #3. Please choose a finish
    Please choose a finish, Standard Black (BK) 122, Coppervein (CV) 122, Stainless Steel Bezel (SS) 322, Solid Brass (BR) 222
  • Step #4. Choose a Standard or Carpet Flange Box type Choose a Standard or Carpet Flange Box type
    Choose a Standard or Carpet Flange Box type Choose a Standard or Carpet Flange Box type, Full Pocket-Standard lid (SL) 002SL, Full Pocket-Carpet lid (CL) 002CL
Customer reviews
Average rating:

Score: 0. Votes: 0
Please sign in to add review
There are no comments yet. Be the first to leave a comment
Customers who bought this product also bought
Drop items here to shop
Product has been added to your cart
  • Choose the product options first
    • $3.00

    Not rated yet
    • 25% less
  • Choose the product options first
    • $2.00

    Not rated yet
  • Choose the product options first
    • $3.97

    Not rated yet
  • Choose the product options first
    • $226.74

    Not rated yet
  • Choose the product options first
    • $9.88

    Not rated yet
    • 18% less
Customers who viewed this product bought
  • Choose the product options first
    • $2.00

    Not rated yet
  • Choose the product options first
    • $588.88

    Not rated yet
    No reviews.
  • Choose the product options first
    • $39.88

    Not rated yet
    • 20% less
  • Choose the product options first
    • $9.88

    Not rated yet
    • 18% less
  • Choose the product options first
    • $3.97

    Not rated yet