Customer service: 800-260-1181
Monday-Thursday 9AM to 5PM EST, Fridays till 3PM. After hours, leave a message, or call our warehouse at 847-220-0396 till 6PM EST
Previous image
Nickel Silver finishing ring with AP-TCP-2-LR cover
Next image
Zoom image

Mistake Rings for bad cuts in the wood or concrete floors

Floor box Finishing Rings in two sizes and four finishes (including custom finishes). Your contractor cut a round hole in the wood for that electrical floor box so you could have that electrical power you always wanted under or near the end table to plug in your laptop, cell phone, or a power cleaning vacuum.  But when he cut the round hole in the floor, he cut the hole too large, and it also has a ragged edge, so how do you fix this?  Arnev Products has a solution for this problem, and has developed a round finishing ring that will be glued to the floor to hide the bad cut. No floor box covers are included with these "Finishing Rings".  If you need a floor box please CLICK HERE

PULL THIS PAGE DOWN TO START ORDERING
 
  • $57.88
Market price: $69.90, you save $12.02
  • 17% less
  • Price Buy
    Brushed Brass lacquer finish $57.88  
    Brushed Aluminum finish $57.88  
    Nickel Silver finish $57.88  
    #1 Pewter Matte $152.88  
    #2 Bronze $132.88  
    #3 Bronze with Gold Wash $132.88  
    #5 Gold $132.88  
    #7 Black $132.88  
    #8 Pewter Bright $152.88  
    #9 Rust $132.88  
    #10 Verdigris $132.88  
    #12 Copper Bright $132.88  
    #13 Copper Bronze $132.88  
    #15 Satin Pearl $132.88  
    #16 Antique Copper $132.88  
    #17 Weathered White $132.88  
    #20 Satin Pewter $152.88  
    #21 Antique Gold $132.88  
    #23 Brushed Natural Pewter $152.88  
    #130 Pewter with Terra-Cotta Wash $152.88  
    #132 Pewter with Bronze Wash $152.88  
    #133 Pewter with Copper Wash $152.88  
    #134 Pewter with Verdi Wash $152.88  
    #135 Pewter with White Wash $152.88  
    #137 Pewter with Cherry Wash $152.88  
    #138 Pewter with Maple Wash $152.88  
    #231 Bronze with Black Wash $132.88  
    #233 Bronze with Copper Wash $132.88  
    #234 Bronze with Verdi Wash $132.88  
    #730 Black with Terra-Cotta Wash $132.88  
    #732 Black with Bronze Wash $132.88  
    #733 Black with Copper Wash $132.88  
    #734 black with Verdi Wash $132.88  
    #736 Black with Chocolate Wash $132.88  
    #737 Black with Cherry Wash $132.88  
    #738 Black with Maple Wash $132.88  
    #739 Black with Steel Wash $132.88  
    #931 Rust with Black Wash $132.88  
    #933 Rust with Copper Wash $132.88  
    #934 Rust with Verdi Wash $132.88  
  • SKU
    Finishing Rings in two sizes
See our new Nickel Silver finsh, great for stainless steel, nickel silver, and aluminum covers that has only a slight brush stroke, or no brushed strokes.
Nickel silver finishing ring with AP-TCP-2-LR floor box coverAluminum Finishing Rings in 7.5
                                           "NEW" Nickel Silver                                                             Brass Finish                                                 Aluminum Finish
 
To order sample chips for $3.00 ea. Click Here
 
Also available in 38 custom finishes
 
Pewter finish price increase: All Pewter finishes will have an additional refinishing charge due to the high cost of plating and polishing needed for these Pewter finishes along with a minimun of 20 rings.
 
Please note:  There are no floor boxes along with our Finishing Rings.  To order floor boxes, see section #16 on the left side margin of every page.
 
There are several Pewter finishes that require more plating and finishing and there is a minimun order of 20 pieces and an additional $35 each, sorry.  This ring will cover areas of tile or wood that has a rough edge around your round electrical floor box cover if it is damaged, or was cut improperly.  
  
Inside round opening (I.D.) is 4 inches, and the overall outer measurement (O.D.) at 7.5" inches is our standard size.  Also available in 4.5" (I.D.) by 7.5" (O.D.).  The Finishing Rings are also available in our 38 custom finishes for an additional charge.  Available in Brass now for $57.88.  However there is an extra charge for each ring with a custom Pewter finish and a minimum order of 20 rings, which need additional plating and refinishing required other than the standard brass, aluminum, and nickel silver standard finishes.  This does include all shipping charges, and there are three of them we have to do.  One to our factory, one to the finishing company, and one back to the customer.
  
You can purchase a sample chip for $3.00 at this page /Custom-Floor-Box-Sample-Chip-Finishes.html and will be sent at no charge with a confirmed order.  Once you receive the sample finish, you will be asked to sign-off for the approved custom finish.  After the final approval, we will start your order, and these are non-refundable in custom finishes.  However, these are not intended for high traffic areas in the custom finishes.  Usually they are under a table for a lamp, or under a desk where they are seen, but not constantly walked across.
 
Here are some other products you might like that could go with this the finishing rings Here
 
 
 
Please read our policy for refinishing floor box covers
 
Thank you for your interest in refinishing your floor box cover in one of our Arnev Products, Inc. custom finishes.  For the protection of your cover, we ask that you follow these instructions.
 
1.  We ask that you send the COVERS ONLY Floor box covers generally come lacquer coated. To refinish the floor box covers, the lacquer must be removed, and this is done by soaking the covers in a strong chemical.  Any non-metallic parts that may be attached to the cover, including gaskets or electrical devices, receptacles, low voltage housings, etc., will be dissolved with the lacquer as well. This is why we insist that only floor box covers be sent for refinishing.  If the cover or receptacle cannot be removed from the floor box, we are unable to soak off the lacquer, and cannot refinish the cover.  Also, no plastic type covers are accepted. We are NOT responsible for the box itself, gaskets or devices, so please keep all the other parts to the assembly, take off the cover, and send only the cover. 
 
2.  Please package any exterior screws (screws that will be visible after the box is installed) with the cover so these can be finished to match the box.  Make sure they are secure so they don't get lost or scratch the cover in transit.
 
3.  Custom colors are run in batches.  Consequently, the finishing time can vary depending upon the schedule for the batch of the custom color you have chosen.  However, as we need only the cover, the floor box itself can be installed by your electrician to maintain your building or remodeling schedule.
 
4.  You have been advised by one of our customer service representatives that the custom finishes are approved for LOW TRAFFIC AREAS ONLY.  Should you decided to install the floor boxes with our finished in HIGH TRAFFIC AREAS, any finishing 1 year limited warranty is void.  In addition, if you should decide to apply any protective finish (lacquer, polyurethane, etc.) OVER our custom finish, the finishing 1 year limited warranty is void.
 
5.  If you approve the enclosed sample and agree to the instructions above, please sign and return the top portion of this page.  You may keep the bottom portion for your records.
 
If you follow these instructions, we are confident that you will love your custom floor box covers, and will enjoy them for years to come.
 
I approve of sample number______________________________ and agree to these instructions.
 
X________________________________________________________________________________________________
   
  • Choose a finish
    Brushed Brass lacquer finish, Brushed Aluminum finish, Nickel Silver finish, #1 Pewter Matte, #2 Bronze, #3 Bronze with Gold Wash, #5 Gold, #7 Black, #8 Pewter Bright, #9 Rust, #10 Verdigris, #12 Copper Bright, #13 Copper Bronze, #15 Satin Pearl, #16 Antique Copper, #17 Weathered White, #20 Satin Pewter, #21 Antique Gold, #23 Brushed Natural Pewter, #130 Pewter with Terra-Cotta Wash, #132 Pewter with Bronze Wash, #133 Pewter with Copper Wash, #134 Pewter with Verdi Wash, #135 Pewter with White Wash, #137 Pewter with Cherry Wash, #138 Pewter with Maple Wash, #231 Bronze with Black Wash, #233 Bronze with Copper Wash, #234 Bronze with Verdi Wash, #730 Black with Terra-Cotta Wash, #732 Black with Bronze Wash, #733 Black with Copper Wash, #734 black with Verdi Wash, #736 Black with Chocolate Wash, #737 Black with Cherry Wash, #738 Black with Maple Wash, #739 Black with Steel Wash, #931 Rust with Black Wash, #933 Rust with Copper Wash, #934 Rust with Verdi Wash
  • Size in 4" or 4.5" inside dimension with 7.5" outside dimension.
    Choose your size, 4" Inside diameter X 7.5" Outside diameter, 4.5" Inside diameter X 7.5" Outside diameter
  • 4-6 weeks delivery on custom finishes. All rings will ship seperately with a floor box order
    4-6 wk. delivery for custom finishes
Customer reviews
Please sign in to add review
There are no comments yet. Be the first to leave a comment
Customers who bought this product also bought
Drop items here to shop
Product has been added to your cart
  • Choose the product options first
    • $4.00

    Not rated yet
    • Free
  • Choose the product options first
    • $3.97

    Not rated yet
  • Choose the product options first
    • $9.88

    Not rated yet
    • 18% less
  • Choose the product options first
    • $73.82

    Not rated yet
    • 3% less
  • Choose the product options first
    • $9.88

    Not rated yet
    • 18% less
Customers who viewed this product bought
  • Choose the product options first
    • $90.72

    Not rated yet
  • Choose the product options first
    • $73.82

    Not rated yet
    • 3% less
  • Choose the product options first
    • $9.88

    Not rated yet
    • 18% less
  • Choose the product options first
    • $114.55

    Not rated yet
    • 8% less
  • Choose the product options first
    • $78.21

    Not rated yet