Double Wide Pocket AV Floor box with room for up to four duplex receptacles or up to 24 low voltage devices.

Double-Wide AV floor box with room for up to four duplex receptacles or up to 24 low voltage devices. The lid will close & the chords will come out the front section. 
 made in the USA
 
 
  • $588.88

Please fill in the dropdown to continue!

Qty:  
  • SKU
    Double Wide Pocket
 
 
Double-Wide AV floor box with room for up to four duplex receptacles or up to 24 low voltage devices. The lid will close, the chords will come out the front section. This has a second small door that lifts and closes shut when not in use to prevent your heel from getting stuck in the opening. For wood or concrete.
 
The Double Wide Stage Pocket has the panel capacity for either:
• (4) #PNL-100 Series "Connectrix" Panels or
• (4) #PE Series Single Gang Electric Duplex Switch Box Panels or
• any combination of the 4 panels, like (1) #PE series and (3) PNL-100 series.

The Double Wide Stage Pocket has the connector capacity for either:
• (24) "Connectrix" Connectors or
• (24) Neutrik® Connectors or
• (24) Switchcraft® Connectors or
• (12) "Connectrix", Neutrik®, or Switchcraft® Connectors and (2) #PE Electric Duplex Switch Box Panels
Price includes panel only. 
CLICK HERE TO ORDER ALL THE AVAILABLE CONNECTORS.
With panels included in Black finish: $588.88
Our starting price is: $588.88
 
 
 
 
Arnev Products extra large-sized Stage Pocket, the Double Wide Stage Pocket, is a standard general use vertical slant panel flush stage pocket.
The Double Wide Stage Pocket is made of heavy duty steel and may be used to conceal audio, communications, control, data, electric AC power,
switches, video, and voice connections etc. below the floor surface for easy access and to prevent connector damage. The Double Wide Stage
Pocket has an extra large capacity inter-changeable panel system which permits easy custom connector/panel configurations.
Utilizing Arnev's "Connectrix" System will allow mounting of up to 24 "Connectrix", Neutrik®, Switchcraft®, and/or Custom Connectors in the Double Wide Stage Pocket. All Arnev Double Wide Stage Pockets are welded steel construction, with a 1/8" (nominally 10 ga. (.135")) thick CRS steel Lid, a 1/8" (nominally 11 ga. (.120")) thick CRS steel Mounting Flange, and a 16 ga. (.062") thick Pocket Body. The Double Wide Stage Pocket resists bending under even the most severe stage loads.

Removable spring loaded hinge pins permits easy exchange of lids for carpet lids, locking lids, standard lids, and other custom application lids. A generous cable way slot of 3/8" x 16" permits easy cable exit from the stage pocket, even for large gauge cables. Two cableway slot channel closures closes the slot when not in use. The Double Wide Stage Pocket has an easy installation into 16.8" x 8.5" cutout in the stage floor. Open easy access from top or back of the Double Wide Stage Pocket to connector panels makes for easy installation.

A scratch/wear resistant finish, oven cured powder coat is electro-staticly applied inside and outside the entire Stage Pocket. Decorator neutral Antique Copper Vein or Textured Black finishes are standard. A Solid Brass Lid and Mounting Flange as well as Solid Stainless Steel Lid and Mounting Flange are also available by special order. The Double Wide Stage Pocket's solid rubber Lid Stops cradle the lid to prevent lid rattle.

Arnev's Standard Vertical Slant Panel Stage Pocket Systems offer "Connectivity" Solutions with a flexible, reliable, and simplistic design. The flexible design of the Standard Vertical Slant Panel Stage Pocket Lid, Mounting Flange and Pocket Body along with Custom and Prefabricated Aluminum "Connectrix" (Neutrik®/Switchcraft® combo cutout) Panels, Switchcraft® Panels, and our large selection of "Connectrix" (Neutrik®/Switchcraft® combo cutout), Switchcraft®, and Custom Connectors allow the Stage Pockets to be installed in many different applications. These applications include educational, institutional, and liturgical settings. Within these applications various audio, communications, control, data, electric AC power, video, and voice terminations are possible, allowing for a complete Stage Pocket System.

Arnev's Standard Vertical Slant Panel Stage Pockets are available in a variety of sizes (Mini, Half, Full, and Double Wide) making them flexible in both form and function and able to meet your individual requirements. All Standard Vertical Slant Panel Stage Pockets are UL Listed except for the Mini Pocket.
 
     
 
  SPECIFICATIONS  
  Double Wide Stage Pocket Body Size = 16.000” W x 4.500” H x 7.187” D
Double Wide Stage Pocket Lid & Mounting Flange Size = 18.500” W x 0.937” H x 10.500” D
Double Wide Stage Pocket Connector Capacity = Up to 24 “Connectrix”, Neutrik®, or Switchcraft®
Double Wide Stage Pocket Cutout Dimensions = 16.800" W x 8.500" H
Double Wide Stage Pocket Material = CRS Steel and/or Solid Half Hard Brass
Double Wide Stage Pocket Panel Capacity =
• (4) #PNL-100 Series “CONNECTRIX” Panels OR
• (4) #PSW-100 Series Switchcraft® Panels OR
• (4) #PE Series Single Gang Electric Duplex Switch Box Panels OR
• (2) #FP3E Series Triple Gang Electric Duplex Switch Box Panels OR
• (2) #PNL-120 Series “Connectrix” Panels
 
     
  CONNECTORS  
 
' Custom Cut Panel Connectors Switchcraft® Connectors
Connectrix Custom Cut Switchcraft®

Neutrik® "D" and Switchcraft® "E" Connector Mounts
Custom Cut Connector Mounts
Switchcraft® "D" Connector Mounts

“CONNECTRIX” CONNECTORS COMBINE NEUTRIK® “D” AND SWITCHCRAFT® “E” MOUNTING HOLE PATTERNS FOR GREATER FLEXIBILITY

The “Connectrix” system connectors may be used in any of the “Connectrix” panels utilizing the popular mounting pattern of the Neutrik “D” and Switchcraft “E” series mounting patterns. Connectors using the generous rectangular “Connectrix” cutout will add to a growing array of adapter-mounted standard connectors. The adapter mount is plastic and provides ground isolation between the panel and connector. Click on the links above for our current selection of stock “Connectrix” system connectors.

When ordering, please specify model number and type of connector as well as panel model number (#PNL-100 Series, #PNL-120 Series, or #PSW-100 Series) the connectors will be loaded into. *NOTE: Specific High Density (HD) and Sub-D pattern connectors will require either 2 or 3 “Connectrix” Horizontal Spaces or 2 or 3 “Connectrix” Vertical Spaces, depending on connectors selected. Connectors may be loaded into panels with nutcerts and nut/bolts or black aluminum pop rivets.
 
     
 
  PANELS  
 
' Custom Cut Panels Switchcraft® Panels
Connectrix Custom Cut Switchcraft®

"Connectrix" Panels combine Neutrik® "D" and Switchcraft® "E" Connector Mounts
Custom Cut Panels with Custom Connector Mounts
Utilize Switchcraft® "D" Connector Mounts

“CONNECTRIX” SYSTEM PANEL DESCRIPTION

Many pre-cut stock #PNL-100 Series, #PNL-120 Series “Connectrix” System connector panels and #PSW-100 Series Switchcraft® connector panels are available for the Double Wide Stage Pocket. Standard "Connectrix" and Switchcraft® Panels are created from high strength, tough, aircraft aluminum alloy (6061-T6) that is 1/16" (.062") or 1/8" (.125") thick. The standard panels mount with (4 or 6) self-tapping screws. Each panel is CNC machined to precisely mate with the designated connectors and in the pocket mounting holes. Each Standard "Connectrix" and Switchcraft® Panel is finished with oven cured semi-gloss black powder coat.

Most panels provide header space for custom engraving which is fast and easily accomplished on a separate dedicated CNC engraving machine. The finished panels show bright aluminum in the engraved characters and need not be back filled. Arnev standard panels are flat, strong, and rigid like the typical thinner mild steel panels. Because the panels are machined and not punched they stay flat and undistorted unlike punched panels which distort in the punching process. The machined “Connectrix” style cutouts combine popular mounting patterns of the Neutrik “D” series and Switchcraft “E” series connectors with a generous rectangular cutout that mates with a growing array of adapter-mounted standard connectors. The adapter mount is plastic and provides ground isolation between the panel and connector.

Using the “Connectrix” system panel it is possible to mount any combination of modular jacks (RJ45, RJ11 etc.), BNCs, dual RCAs, mic jacks, speaker jacks and numerous other standard connectors without a single custom punch. This system provides for more connectors and mounting options in stock standard Arnev panels. The benefit is faster order turn around and lower cost. Less custom fabrication for custom spec results with off-the-shelf stock prices.
 
     
 
  PANEL CAPACITY - #124xxxx DOUBLE WIDE POCKET  
  The Double Wide Stage Pocket has the panel capacity for either:
• (4) #PNL-100 Series "Connectrix" Panels or
• (2) #PNL-120 Series "Connectrix" Panels or
• (4) #PSW-100 Series Switchcraft® Panels or
• (4) #PE Series Single Gang Electric Duplex Switch Box Panels or
• (2) #FP3E Series Triple Gang Electric Duplex Switch Box Panels

The Double Wide Stage Pocket has the connector capacity for either:
• (24) "Connectrix" Connectors or
• (24) Neutrik® Connectors or
• (24) Switchcraft® Connectors or
• (12) "Connectrix", Neutrik®, or Switchcraft® Connectors and (2) #PE Electric Duplex Switch Box Panels

 
     
 
  PANEL CONFIGURATIONS  
PE PNL-100      
SERIES PANELS SERIES PANELS      
#PE #PNL-100      
     
#FP3E #PNL-102      
     
#PNL-103      
     
#PNL-104      
     
#PNL-105      
     
#PNL-106      
     
     
     
     
  INCLUDES  
 
• (1) Stage Pocket Body with Trim Bezel Mounting Flange
• (1) Lid
• (2) Hinge Pins
• (2) Springs
• (16) #8 Self Tapping Sheet Metal/Wood Screws
• (2) Slot Closures
 
     
  ORDERING  
 
When ordering Stage Pockets please specify the following:
Stage Pocket Model Number: Example - #124SLBK
Stage Pocket Model Name (size): Mini | Half | Full | Double Wide
Stage Pocket Finish Type (Lid & Mounting Flange): Black, Brass, Copper Vein, Stainless Steel
Stage Pocket Lid Type: Carpet Lids (CL), Locking Lids (LL), Standard Lids (SL)
Optional Stage Pocket Panel(s) Model Numbers: Example - #PNL-106
Optional Connectors to be loaded into Panel(s): Example - #C15101
Location of Connectors mounted into Panel(s): Example - Top Left
Type of Connector Mounts: Nuts/Bolts or Black Aluminum Pop Rivets
 
     
 
     
     
     
 
  FEATURES  
 

EXTRA LARGE CAPACITY: The Double Wide Stage Pocket accomodates #PNL-100 Series Panels, #PSW-100 Series Panels, #PNL-120 Series Panels, #PE Series Panels, and #FP3E Series Panels in an interchangeable multi-panel system making for easy custom configurations. Four (4) optional #PNL-100 Series Panels or two (2) optional #PNL-120 Series Panel will mount up to 24 "CONNECTRIX", Neutirk®, and/or Switchcraft® type connectors*. Four (4) optional #PSW-100 Series Panels will mount up to 24 Switchcraft® type connectors.

DURABLE CONSTRUCTION: Welded steel construction of Double Wide Stage Pocket Lid, Mounting Flange, and Pocket Body resist bending under even the most severe stage loads. The Lid is made from 10 gauge (nominally (.135")) thick CRS steel, the Mounting Flange is made from 1/8" (nominally 11 ga. (.120")) CRS thick steel, and the Pocket Body is made from 16 ga. (.062") thick CRS steel.

SPRING LOADED HINGE PINS: Removable spring loaded hinge pins permit easy exchange of lids for Carpet Lid (CL), Locking Lid (LL), Standard Lid (SL) and custom application lids.

CABLE WAY SLOTS: Generous 3/8" x 16" Cable Way Slots permit easy cable exit from pocket(s), even for large gauge cables. Two Cable Way Slot Channel Closures closes slot when not in use.

EASY INSTALLATION: Easy installation into 16.8" x 8.5" rectangular cutout in stage floor. Open easy access from the top or back of the stage pocket allows simple connector/panel terminations.

DECORATOR FINISHES: Scratch/wear resistant finish, oven cured powder coat electro-static applied inside and outside entire Double Wide Stage Pocket. Decorator neutral Antique Copper Vein and Textured Black finishes are standard. A Solid Brass Lid and Mounting Flange as well as Solid Stainless Steel Lid and Mounting Flange with brushed finishes are also available by special order.
If you need a custom color, check out our Custom Color Finishes.  You will need to ask for a quantity quote, or a custom color quote at 800-260-1181.  Please allow 2-3 weeks for delivery on these custom colors.
 

RUBBER LID STOPS: Rubber lid stops set into recessed mount cradle the lid to prevent lid rattle.
 
     
  FINISHES  
 
DECORATOR FINISHES:
 Arnev Double Wide size Standard Vertical Slant Panel Stage Pockets come with a scratch/wear resistant finish, oven cured powder coat electro-static applied inside and outside the entire Full Stage Pocket. Decorator neutral Antique Copper Vein and Textured Black finishes are standard. A Solid Brass Lid and Mounting Flange as well as a Solid Stainless Steel Lid and Mounting Flange with a brushed finish are also available by special order*.

 
     
 </>
 
MATERIALS
 

STANDARD POCKET MATERIALS: Arnev Double Wide size Standard Vertical Slant Panel Stage Pocket Lids are made from 10 gauge (nominally (.135")) thick CRS steel, the Mounting Flange is made from 1/8" (nominally 11 ga. (.120")) CRS thick steel, and the Double Wide Pocket Body is made from 16 ga. (.062") thick CRS steel. The exception to this is the Brass Double Wide Stage Pocket Lid which is made from 10 gauge (nominally (.135")) thick Half Hard Solid Brass and Mounting Flange which is made of 1/8" (nominally 11 ga. (.120")) thick Half Hard Solid Brass with a Stage Pocket Body made from 16 ga. (.062") thick CRS steel.

Double Wide Stage Pockets are manufactured with the following materials:
• Lids are made from 10 gauge (nominally (.135")) thick CRS steel<br

 

UL LISTED: UL Listed compliance Standard 514A file FLOOR BOX 44LK Suitable for raised floor applications.

UL Listed
UL Listed Copy
Sales Taxes please note:  All our AV boxes are shipped direct to you from our California facility and if you are having the box shipped to you in California we will be calculating the sales tax needed for the transaction.  By law, we are required to charge and pay California sales taxes when a product is shipped to a customer in California.
  • Step #1. Choose Small Panel #1 --- FOUR SMALL PANELS NEEDED FOR THIS BOX.
    Choose panel #1, #PNL-100 small panel with no holes, #PNL-102 small panel with two holes, #PNL-103 small panel with three holes, #PNL-104 small panel with four holes, #PNL-105 small panel with five holes, #PNL-106 small panel with six holes, #PE small panel for duplex, #PNL-107 for Decora Type Receptacle
  • Step#2. Choose Small Panel #2 --- FOUR SMALL PANELS NEEDED FOR THIS BOX.
    Choose panel #2, #PNL-100 small panel with no holes, #PNL-102 small panel with two holes, #PNL-103 small panel with three holes, #PNL-104 small panel with four holes, #PNL-105 small panel with five holes, #PNL-106 small panel with six holes, #PE small panel for duplex, #PNL-107 for Decora Type Receptacle
  • Step #3. Choose Small Panel #3 --- FOUR SMALL PANELS NEEDED FOR THIS BOX.
    Choose panel #3, #PNL-100 small panel with no holes, #PNL-102 small panel with two holes, #PNL-103 small panel with three holes, #PNL-104 small panel with four holes, #PNL-105 small panel with five holes, #PNL-106 small panel with six holes, #PE small panel for duplex, #PNL-107 for Decora Type Receptacle
  • Step #4. Choose Small Panel #4 --- THEN CLICK ON CONNECTORS UNDER THE "ADD TO CART" BUTTON BELOW.
    Choose panel #4, #PNL-100 small panel with no holes, #PNL-102 small panel with two holes, #PNL-103 small panel with three holes, #PNL-104 small panel with four holes, #PNL-105 small panel with five holes, #PNL-106 small panel with six holes, #PE small panel for duplex, #PNL-107 for Decora Type Receptacle
  • Step #5. Choose a finish:
    Choose a finish, Black (BK) 124, Coppervein (CV) 124, Stainless Steel (SS) 324, Solid Brass (BR) 224
  • Step #6. Choose a Standard or Carpet Flange Box type
    Choose a lid type (Standard lid or Carpet lid), Standard lid (SL) 004, Carpet lid (CL) 004
  • Step #6. Please choose for Wood, or Concrete pour type WITH OR WITHOUT POWER RECEPTACLE.
    Choose for Wood or Concrete floor, Wood Floor, Concrete Pour NO Power (104-BBX), Concrete Pour WITH Power (ISO 104-BBX)
Customer reviews
Average rating:

Score: 0. Votes: 0
Please sign in to add review
There are no comments yet. Be the first to leave a comment
Customers who bought this product also bought
Drop items here to shop
Product has been added to your cart
  • Choose the product options first
    • $3.00

    Not rated yet
    • 25% less
  • Choose the product options first
    • $3.97

    Not rated yet
  • Choose the product options first
    • $226.74

    Not rated yet
  • Choose the product options first
    • $2.00

    Not rated yet
  • Choose the product options first
    • $149.92

    Not rated yet
Customers who viewed this product bought
  • Choose the product options first
    • $2.00

    Not rated yet
  • Choose the product options first
    • $293.88

    Not rated yet
  • Drag and drop me to the cart
    • $117.40

    Not rated yet
  • Choose the product options first
    • $9.88

    Not rated yet
    • 18% less
  • Choose the product options first
    • $73.82

    Not rated yet
    • 3% less