Customer service: 800-260-1181
Monday-Thursday 9AM to 4PM Central time, Fridays till 3PM Central time.

Why shipping is so expensive at this time?

Previous image
AP-812-DFB-LR-W/2XLR Floor Box for XLR Microphone jacks
Next image
Zoom image

XLR Floor Box for 2 Mic Jacks and flush mount floor box

Round AV floor box. Flush mount for Wood and Concrete floors. This audio-video floor box comes with two female XLR connectors as standard.  But, this will hold almost ANY TWO SMALL AV CONNECTORS or one large connecter for an additional charge and you will need to order them at this page Available Here.  These electrical audio-video floor boxes are available in Solid Brass or Brushed Aluminum covers, with our custom 38 finishes, so check them out.

 
  • $231.88
Market price: $289.99, you save $58.11
  • 20% less
Qty:  
  • SKU
    AP-812-DFB-LR-W/2XLR

 

812-DFB SERIES

Installation Instructions
 
1. For wood floors
 
a. Using a 4” hole saw, cut the flooring to a depth equal to the thickness of the cast
flange and cover assembly being used on the floor box.
 
b. Center a 3.5” hole saw in the 4” opening and cut through all remaining layers of flooring.
This will create a lip for the flange of the box to rest on.
 
c. Remove cover assembly and wiring device from floor box.
 
d. Dropbox body into the opening and secure using #6 wood screws (not provided) through
the countersunk slots in the cast flange and into the underlying wood.
 
e. After wiring and installing electrical or communication devices to the floor box and ground
screw (if applicable), replace the cover plate assembly using #8/32 x ½” screws provided.
 
f. If an uneven cut was made into the flooring, goof rings (TCP-GR1) can be used in conjunction
with the original cover assembly or oversized covers (TCP series) can be used in place of the
original cover assembly.
 
g. For carpeted areas, use SCF-1 placing on top of floor box (cover assembly removed first),
then inserting the cover assembly into carpet flange. Use 1.25” longer screws provided through
the cover assembly and that will affix to the floor box.
 
h. For tile applications, order part #812 (box body only) and a TCP style cover. Follow steps a-d
above. After wiring in step e, install mounting plate and gasket, then place TCP style plate
on top of the floor and use #8/32 X ¾” screws provided.
 
2. For concrete floors
 
a. Not recommended for new construction as no concrete cap is provided and this is a nonadjustable box.
 
b. Core out 4 ¼” into concrete as deep as needed to accommodate the height of the box and ability to
affix conduit from underneath.
 
c. Backfill concrete if necessary to close gaps in the floor.
 
d. Follow steps c-h above.

Available Now!

Round AV floor box with flip lids.  Flush mount for Wood or Concrete floors.  This comes with two female XLR microphone connectors already mounted, the floor box and cover, and the rubber gasket. 
 
This will hold almost any TWO SMALL AV CONNECTORS, or one large connector, and these connectors are available in the largest selection of any AV connectors on the web at an extra charge, so click here to order other Available Connectors.
 
NOTE: If you are ordering only one small connector, you will need our model number #C-15112 Neutrik Blank Plug Panel Mount Connector for $4.00, to take up the open space normally used for the second connector. 
 
Available in Solid Brass or Brushed Aluminum Covers.
 
Ou price is $231.88, which includes the floor box, solid brass cover, AV housing (with two XLR female connectors), and rubber gasket.
 
 
Immediate delivery:
 
 
 
To order custom finishes CLICK HERE!
 
  Click to view available Finishes
 
 
Please read our policy for refinishing floor box covers
 
Thank you for your interest in refinishing your floor box cover in one of our Arnev Products, Inc. custom finishes.  For the protection of your cover, we ask that you follow these instructions.
 
1.  We ask that you send the COVERS ONLY Floor box covers generally come lacquer coated. To refinish the floor box covers, the lacquer must be removed, and this is done by soaking the covers in a strong chemical.  Any non-metallic parts that may be attached to the cover, including gaskets or electrical devices, receptacles, low voltage housings, etc., will be dissolved with the lacquer as well. This is why we insist that only floor box covers be sent for refinishing.  If the cover or receptacle cannot be removed from the floor box, we are unable to soak off the lacquer, and cannot refinish the cover.  Also, no plastic type covers are accepted. We are NOT responsible for the box itself, gaskets, or devices, so please keep all the other parts to the assembly, take off the cover, and send only the cover. 
 
2.  Please package any exterior screws (screws that will be visible after the box is installed) with the cover so these can be finished to match the box.  Make sure they are secure so they don't get lost or scratch the cover in transit.
 
3.  Custom colors are run in batches.  Consequently, the finishing time can vary depending upon the schedule for the batch of the custom color you have chosen.  However, as we need only the cover, the floor box itself can be installed by your electrician to maintain your building or remodeling schedule.
 
4.  You have been advised by one of our customer service representatives that the custom finishes are approved for LOW TRAFFIC AREAS ONLY.  Should you decided to install the floor boxes with our finished in HIGH TRAFFIC AREAS, any finishing 1-year limited warranty is void.  In addition, if you should decide to apply any protective finish (lacquer, polyurethane, etc.) OVER our custom finish, the finishing 1-year limited warranty is void.
 
5.  If you approve the enclosed sample and agree to the instructions above, please sign and return the top portion of this page.  You may keep the bottom portion for your records.
 
If you follow these instructions, we are confident that you will love your custom floor box covers, and will enjoy them for years to come.
 
I approve of sample number______________________________ and agree to these instructions.
 
X________________________________________________________________________________________________
 
 
  • Choose a finish for the cover
    Please choose a finish (Brass or Aluminum), Solid Brass (AP-812-DFB-LR-W/2XLR) with brass cover), Aluminum (AP-812-DFB-LR-W/2XLR-A) with aluminum cover
Customer reviews
Please sign in to add review
There are no comments yet. Be the first to leave a comment
Customers who bought this product also bought
Drop items here to shop
Product has been added to your cart
  • Choose the product options first
    • $4.00

    Not rated yet
  • Choose the product options first
    • $78.21

    Not rated yet
  • Choose the product options first
    • $105.99

    Not rated yet
Customers who viewed this product bought
  • Drag and drop me to the cart
    • $144.37

    Not rated yet
  • Drag and drop me to the cart
    • $18.30

    Not rated yet
  • Drag and drop me to the cart
    • $18.24

    Not rated yet
  • Drag and drop me to the cart
    • $108.28

    Not rated yet
  • Choose the product options first
    • $4.00

    Not rated yet