Customer service: 800-260-1181
After hours: 847-220-0396 till 6 PM Central time
Monday-Thursday 9 AM to 5 PM Central time, Fridays to 3 PM Central time.
Previous image
Frosted glass switch plate covers
Next image
Zoom image

Frosted Real Glass Switch plates

We've all seen Frost on a Window, right? Well, that's what this frosted glass switch plate covers look like. They are very different, and very attractive  So, please check out these Frosted Glass Switch Plate Receptacle Covers, our customers love them.

PLEASE ORDER ONLY ONE FROSTED SWITCH PLATE COVER TO MAKE SURE THESE FROSTED GLASS WALL PLATES ARE GOING TO WORK FOR YOU

Make sure the sound is on the video 

To order our new Screwgard Gaskets, Click Here
 
TO SEE THE SIZE OF THIS PRODUCT, PULL THE PAGE WAY DOWN TO THE BOTTOM, AND THEY ARE THERE FOR YOU TO CHECK OUT.
 
Prices Starting at:
 
  • $25.97
Market price: $35.00, you save $9.03
  • 26% less

  • Price Buy
    A. Single Switch $25.97  
    B. Outlet Covers 2 oval shaped holes $25.97  
    C. Double Switch $30.97  
    D. Combo Switch $31.97  
    E. Triple Switch $40.97  
    F. Ground fault/Rocker. Also for GFI $32.97  
    G. Dbl. Switch Outlet Cover $40.97  
    H. Ground fault/Single Switch $39.97  
    I. Double Outlet Cover 4 oval shaped holes $39.97  
    J. Triple Ground fault/Rocker. Also for GFI $48.97  
    K. double Ground fault/Rocker. Also for GFI $34.97  
    L. Quad Switch $50.97  
    M. Ground fault/Double Toggle $39.97  
    N. Quad Ground fault/Rocker. Also for GFI $60.97  
    O. Outler Cover Triple Switch $60.97  
    P. Ground fault Triple Switch $61.97  
    Q. Ground fault/Double Switch $50.97  
    AA. Frosted Glass switch plate with a hole for a Cable TV (not included) or for a Round Dimmer Knob. $31.97  
    BB. Telephone Frosted Glass Plate with a six wire telephone jack included. $45.97  
    CC. Single Blank $25.97  
    Single size gasket (may be needed) approx. 3 1/2" wide by 5 1/4" high $8.09  
    Double size gasket (May be needed) approx. 5 1/4" wide by 5 1/4" high $9.09  
    Triple size gasket (May be needed) approx. 7 1/4" wide by 5 1/4" high $10.09  
    Quad size gasket (May be needed) approx. 9" wide by 5 1/4" high $11.09  

  • SKU
    Frosted Read Glass Switch plates

We manufacture the USA Electrical Standard Decora or GF opening of 1-5/16" wide, by 2-5/8" High,

If your Decora, or GF-type receptacles are different from this, you must let us know before you start,  as some of the Lutron and Leviton receptacles will not fit our glass switch plate covers.

 

 
 
Here is how the telephone device is mounted on Clear, Mirrored, or Frosted Glass switch plates.
Peel and stick on the back sides of the plate and position the telephone device in the 
center of the 5/8th inch hole for the telephone wire to go through and into the phone plug.
 
AND WITH GLASS BEING FLAT ON THE BACK SIDES, SOMETIMES INSTALLATION IS A BIT DIFFICULT, SO WE HAVE DEVELOPED A PRODUCT CALLED SWITCHGARDS, SO SEE OUR VIDEO BELOW TO SHOW HOW TO MAKE THE FROSTED GLASS SWITCH PLATES EASY TO INSTALL. 
 
Telephone Jack installation on Glass Switch Plates, Acrylic, and Frosted using our Screwgard Gaskets Below
 
The telephone jack for all the glass and acrylic switch plates is always a 3/8 inch hole in the glass.  Then the telephone plug in an almond color that is supplied has two peel-and-stick pieces of sticky paper on one side of the new telephone plug, which you peel and stick on the BACKSIDE of the glass, and you have to line it up so the telephone jack cord can go through that hole on the front of the glass to plug into the new telephone jack positioned on the backside of the glass, acrylic, or the Screwgard paintable gasket.   This new almond color jack is to replace whatever you have on the wall, and it is color-matched to attach the same color wires (Red-Green-Black-White, etc.) coming out of the wall to the new telephone jack on the backside of the glass switch plates.  Now, this mounting of the new telephone jack on the backside of the glass should be done AFTER the glass plate has been painted on the backsides to the color of your choosing.
 
See this video on how to install a receptacle for a glass backsplash
 
Here are some sample installations of how receptacles are to be installed
 
 
 
Please read this for the Tile Installers:
 
If you would like to use the clear beveled glass with NO PAINTING on the backsides, you will need to have your tile installers put the tile up to the receptacles, and not just end at the box in the wall or you will see the wires in the wall.   If you are using a standard duplex receptacle with two rounded-shaped holes, we would advise you to replace them with a Decora-style duplex with a large rectangular shape, as this will be easy to put the tiles to the receptacles.  See below:

Glass Mirrored/Frosted Glass/Jeweled Tone, and Clear Glass sizing:

All glass products at 3/16th thick, and 5/16 on the bevel

 

One-gang switchplates
(Singles-A, Single Outlets-B, Single Groundfaults-F, Single Blanks, etc.)
 3 1/2" wide by 5 1/4" high
Two-gang switchplates
(Doubles-C, Combo's-D, Double Groundfaults-K, Double blanks, etc.)
 5 1/4" wide by 5 1/4" high
Three-gang switchplates
(Triples-E, Triple Groundfaults-J, Groundfault/Double Switch-Q, etc.)
 7 1/4" wide by 5 1/4" high
Four-gang switchplates
(Quad Switches-L, Outlet Cover/Triple Switch-O, etc.)
 9" wide by 5 1/4" high
Five-gang switchplates
(5-Switch-5S, 5-Groundfault/Rocker-5 GF/R)
 11" wide by 5 1/4" high
Six-gang switchplates
(6-Switch-6S, 6-Groundfault/Rocker-6 GF/R)
 12 5/8" wide by 5 1/4" high
 
We've all seen Frost on a Window, right? Well, that's what these frosted glass switchplates look like. Very different and attractive.
 
Like all glass, these do have a slight greenish tint on the edges of the switchplates, and this is usually never a problem, but we needed to let our customers know exactly what they are going to look like.
 

glass switch plate gaskets

You might need a gasket with your glass switch plates.  If the plug or switch in the wall is sticking out too far, the glass switch plate may not fit snugly against the wall.  Since all glass switchplates are flat on the backsides, our gaskets peel and stick to the outer edges of the backsides, and let the plug or switch extend into the plate, and let the glass plate fit snugly against the wall for the best-desired appearance.
 
The gaskets at about 1/8th inch clear acrylic, and almost disappear when installed correctly and allow the glass switch plate to fit tight against the wall.  In some cases, you may need two gaskets.  They are available in 4 sizes for the 1-2-3-4 gang switch plates.  Please review the installation instructions by scrolling down this page for more information.
 
 
Frosted Glass Switchplates are available in 32 configurations. All our glass switchplates are referred to as mid-sized parts. They are a bit larger than the standard size, but not oversized. All Frosted Glass switchplates include screws. For switchplate sizing, please click here.
How to install a glass switch plate cover without breaking it, click here:  "Frosted Glass Switchplates Installation" 

How to install a glass switchplates without breaking it

So you need to replace the glass switchplates in your bathroom or mirrored wall in your home? Well, it should be an easy accomplishment, but it’s a bit more difficult than you would imagine to “do it right”.
 
There are a few things to think about, and the first is that glass mirrored switch plates are flat on the backside, and not like standard wall plates, which are not. If you think you just need to get out the screwdriver, and away you go, don’t hold your breath, as it’s not that easy.
 
There are two ways to attach this to your receptacles and you will see diagrams of both ways to do this, so choose which one is the best for your situation. In the first figure, we are going to use a duplex receptacle. Some have two screws and some only have one screw, but all the switches and receptacles work with the same method.  Please follow these directions and your glass switchplates installation will be a breeze.
 
 
Figure 1 – With the use of an Acrylic Gasket
glass switchplates when using acrylic gasket
 
Figure 2- With the use of Vinyl Tubing
glass switch plates installation instructions
  1. Let’s start by turning off the electricity to that switch or outlet, removing the existing plate from the wall, and unscrewing the electrical receptacle with the mounting screws. Then carefully pull the receptacle out of the box to give yourself some room to make the following adjustments below in section 2 to section 7, but make sure the power is off to that receptacle before you start pulling it out of the box.
  2. Check to make sure that the facing surface of the conduit box fixture in the wall is flush with the wall, and secure that glass plate to the fixture.
  3. If the box in the wall is recessed, you must install the screw spacer (Steps 4-7). Otherwise, by tightening the screws, you will pull the glass plate into the box in the wall, and this will cause it to crack or break.
  4. Measure the recessed distance from the front wall surface to the conduit box flange.
  5. Cut the plastic screw spacer at the measured length and install it on the top and bottom mounting screws behind the flanges of the electrical fixture. (See the illustration above).
  6. Now with the spacers attached, then place the electrical fixture back in the conduit box in the wall and affix it to the conduit box. You might want to put a piece of electrical tape over the heads of the conduit box mounting screws, as they could be resting on the backside of the glass switch plate, and might take the reflective paint off the back if they are touching too hard.
  7. Hold the glass plate up to the electrical fixture and check to make sure the fixture is fitting flush against to back of the glass switchplate. If it is not, the glass switchplate may bend in and break when you tighten it to the electrical fixture.
  8. Remember that the glass switchplate is flat on the backside unlike a normal switch plate which has a concaved back, and the receptacle may not come all the way out to the front of the glass switchplate, and this is normal, as the glass in beveled for easy access to the plug or switch.
  9. If the glass switch plate does not bump up against the wall because your box in the wall may be out too far, you may need an inexpensive acrylic spacer plate that takes up the distance between the wall and the back of the glass switch plate.
  10. This may all sound complicated, but it’s not, so take your time and your glass switchplates will look great for years to come.
  11. You may also want to choose any of the mirrored accessories for your project for that special touch.

How to install glass switchplates correctly, and you will be a happy customer.

These are mirrored switch plates that are custom frosted and available in these configurations:
Frosted Glass switchplate configurations
  • Step 1: NEW FEATURE! Choose all the quantities of the configurations in one step, then click the Add to Cart button, it's as easy as 1-2-3
    A. Single Switch, B. Outlet Covers 2 oval shaped holes, C. Double Switch, D. Combo Switch, E. Triple Switch, F. Ground fault/Rocker. Also for GFI, G. Dbl. Switch Outlet Cover, H. Ground fault/Single Switch, I. Double Outlet Cover 4 oval shaped holes, J. Triple Ground fault/Rocker. Also for GFI, K. double Ground fault/Rocker. Also for GFI, L. Quad Switch, M. Ground fault/Double Toggle, N. Quad Ground fault/Rocker. Also for GFI, O. Outler Cover Triple Switch, P. Ground fault Triple Switch, Q. Ground fault/Double Switch, AA. Frosted Glass switch plate with a hole for a Cable TV (not included) or for a Round Dimmer Knob., BB. Telephone Frosted Glass Plate with a six wire telephone jack included., CC. Single Blank, Single size gasket (may be needed) approx. 3 1/2" wide by 5 1/4" high, Double size gasket (May be needed) approx. 5 1/4" wide by 5 1/4" high, Triple size gasket (May be needed) approx. 7 1/4" wide by 5 1/4" high, Quad size gasket (May be needed) approx. 9" wide by 5 1/4" high
  • Please choose an insert color if a TV or Telephone plate was ordered
    I did not choose a TV or Telephone type switch plate, Gray, Black, White, Brown, Almond, Ivory
Customer reviews
Please sign in to add review
There are no comments yet. Be the first to leave a comment
Customers who bought this product also bought
Drop items here to shop
Product has been added to your cart
  • Choose the product options first
    • $3.00

    Not rated yet
    • Free
  • Choose the product options first
    • $3.50

    Not rated yet
    • 13% less
  • Choose the product options first
    • $9.95

    Not rated yet
    • 29% less
  • Choose the product options first
    • $10.97

    Not rated yet
    • 22% less
  • Choose the product options first
    • $7.97

    Score: 5.00 (votes: 1)
    • 20% less
Customers who viewed this product bought
  • Choose the product options first
    • $9.95

    Not rated yet
    • 29% less
  • Choose the product options first
    • $7.97

    Score: 5.00 (votes: 1)
    • 20% less
  • Choose the product options first
    • $10.97

    Not rated yet
    • 22% less
  • Choose the product options first
    • $3.00

    Not rated yet
  • Choose the product options first
    • $3.50

    Not rated yet
    • 13% less